merchant circle

Under orthogonal cutting condition, a turning operation is carried out on a metallic workpiece at a cutting speed of 4 m/s. The orthogonal rake angle of the cutting tool is 5º. The...

In an orthogonal machining operation, the cutting and thrust forces are equal in magnitude. The uncut chip thickness is 0.5 mm and the shear angle is 15°. The orthogonal rake angle...

In an orthogonal cutting process the tool used has rake angle of zero degree. The measured cutting force and thrust force are $$500$$ $$N$$ and $$250$$ $$N,$$ respectively. The coe...

A single point cutting tool with $${0^0}$$ rake angle is used in an orthogonal machining process. At a cutting speed of $$180$$ $$m/min$$ the thrust force is $$490N.$$ If the coeff...

Which pair of following statement is correct for orthogonal cutting using a single-point cutting tool? $$P.$$ reduction in friction angle increases cutting force $$Q.$$ Reduction i...

In orthogonal turning of a bar of $$100$$ $$mm$$ diameter with a feed of $$0.25$$ $$min/rev,$$ depth of cut of $$4$$ $$mm$$ and cutting velocity of $$90$$ $$m/min,$$ it is observed...

In orthogonal turning of a bar of $$100$$ $$mm$$ diameter with a feed of $$0.25$$ $$min/rev,$$ depth of cut of $$4$$ $$mm$$ and cutting velocity of $$90$$ $$m/min,$$ it is observed...

Orthogonal turning is performed on a cylindrical work piece with shear strength of $$250Mpa.$$ The following conditions are used: cutting velocity is $$180m/min,$$ feed is $$0.2mm/...

In orthogonal turning of low carbon steel pipe with principal cutting edge angle of $$90,$$ the main cutting force is $$1000$$$$N$$ and the feed force is $$800N.$$ The shear angle...

In an orthogonal machining operation: $$\,\,\,\,\,\,\,\,\,\,$$Uncut thickness $$\,\,\,\,\,$$ $$= 0.5$$ $$mm$$ $$\,\,\,\,\,\,\,\,\,\,$$Cutting speed $$\,\,\,\,\,\,\,\,\,\,$$ $$= 20$...

In an orthogonal machining operation: $$\,\,\,\,\,\,\,\,\,\,$$Uncut thickness $$\,\,\,\,\,$$ $$= 0.5$$ $$mm$$ $$\,\,\,\,\,\,\,\,\,\,$$Cutting speed $$\,\,\,\,\,\,\,\,\,\,$$ $$= 20$...

In an orthogonal cutting test on mild steel, the following data were obtained Cutting speed: $$40$$ $$m/min,$$ Depth of cut: $$0.3$$ $$mm,$$ Tool rake angle : $$ + {5^ \circ },$$ C...

A tube of $$32mm$$ outside diameter was turned on a lathe and the following data was obtained Rake angle $$=35deg,$$ Feed rate $$=0.1mm/rev$$ Cutting force $$=2000N,$$ Cutting spee...

In a typical metal cutting operation, using a cutting tool of positive rake $$\gamma = 10\deg ,$$ it was observed that the shear angle was $$20deg$$. The friction angle is

While turning a $$C15$$ steel of $$160mm$$ diameter at $$215rpm,$$ $$2.5mm$$ depth of cut and feed of $$0.16mm/rev$$ by a tool of geometry $$0-10-8-9-15-75-0mm,$$ the following obs...

In an orthogonal cutting operation on a work piece of width $$2.5mm,$$ the uncut chip thickness was $$0.25$$ $$mm$$ and the tool rake angle was $$0$$(zero) degrees. It was observed...

In an orthogonal cutting test on the following data were obtained Uncut chip thickness $$=0.25mm,$$ Cutting speed: $$60m/min,$$ Tool rake angle: $$0$$ Chip thickness $$0.75mm,$$ Cu...

During orthogonal turning of a steel rod by zero rake tool at feed $$0.25mm/rev$$ and depth of cut $$2.0mm,$$ the following observations were obtained. Tangential component of cutt...